Posts

Spring Project - Finished

Image
 horaaaaaaay! It's finally done :) The scoot is roaring and I could not even finish the drive-in procedure because of the 'silent hour' which starts at 21:00 :/ Anyways, long story short , let's get to pictures: First thing I had to adjust the carb so it idles and starts properly - so this was just for some 20minutes or so :D  Then , afterwards.... I had to remove the fuel till' half of tank  And the reason for that was ,because I had to lower it in order to reach and remove the old piece of... :D potentiometering device called the fuel gauge (that's the old one)  Allrighty then! :) After everything has been replaced and the scooter has been adjusted for proper operation here are some pic's to view and check how the scooter looks :))) bzzzt stealthy black matt' :D Ready2Drive ! :) And that's about it! Mostly the time was spent waiting for the parts to arrive, nevermind that - it was fun to wait and replace everything! Cheers! :) 
Post a Comment
Read more

Spring Project [p3]

Image
 hehehehehe :) Nicccce.  Today,this morning a little after 12pm I finally recieved some long awaited ordered parts! High flow oil pump , 100cc cylinder kit with head and rocker arms also the 'sport' camshaft :D Sport CDI and coil which came in together with the order  not- I'm not gonna be using. N' re-jetted carb. for less hassle  those unknown weight rollers are also out of menu :D  A little peek in the process: at this point my hands were getting too oily and I was diving pretty deep in the bolting process so there are no extra pic's ,sorryz. After everything is setted up properly,regulated n stuff - then I'll post the last part where it purrs and some pic's of scooter itself :) Cya !!!
Post a Comment
Read more

ufo?

Image
 what in the... ? I was just lookin' back at some old photos of previous scoot... and I stumbled across something that can't be indentified... I wonder what is it... and on the bottom is the original photo - not edited or anything ...  weird.....
Post a Comment
Read more

Spring Projector [p2] :)

Image
 Hojjjjjjjaaaaaa. This was a nice sunny day , so I did sum' stuff for the skuut :)       here's sum' parts list. the one's with the "okay" tick are installed :) yippp The spark plug could not be installed yet ,because I'm still waiting for the new cylinder kit >:) Sooo I installed a new Glixal Performance Clutch which came with red torque spring and red small springs :) , nice choice for acceleration that I will be needing :) (there's no actual point to have top speed in my situation :))  )  , of course the vario belt was a little struggle to push on brand new clutch , but I managed it :D (as usual)  aaand also Malossi 6gram rolls have been installed for so-so accel. :)  The 'high-voltage' ignition coil has been installed ,also the tank vacuum pump and filter :-) also painted a little piece of the tank :D  mmm,yummy, a fresh new engine oil :)  :D lold about the advertisment on the package : Power Release Technology , SUPERIOR ...
Post a Comment
Read more

Spring Project: KILLER-BEE CUSTOM :)) :D [p1]

Image
 Halllooo, good day, dear reader :) Let's see... Did I just buy a new scooter ,again ? :D  khh, of course I did! :) Because I love to get my hands dirty and spend time in the garage just' fixin' stuff Computers,electronics and stuff are fun also , but don't know why... - this oily,screw threaded theme kinda submerges me more in the liking. Hard to say why , but da' hell , it's nothing bad ;) So I just enjoy it. So a short intro follows: Bought this little kumoss at dirt cheap money (incl. diesel and trailer rent) , as I see by registration data I'm the third owner for this thing. It has been staying for 1,5.years without any real usage, outside, thankfully under a cover. The visual condition.... Weelll , not the worst , but not the best also! You may be the judge: yyep, as mentioned: not the worst not the best. Anyhow , I disassembled some of the plastic parts and also other stuff away from the body later on.  Also , did an ultrasonic cleaning on the screws ...
Post a Comment
Read more

Last Repair's done on the RB-50

Image
 O Ya. It's been a while since my last post.. So Intro apart - I do did change the transmission and engine block bearings :) Also brought some goodies for a swap. You'll see the story below I had to buy tool kit just specially to remove the old bearings...                                                            Rear Engine part (old one's) Transmission block with old one's OUT with the old one's Out with these aswell And as for installation I used some grease and hair dryer  ,also adding a hammer - nothing beats this combination :D The whole engine had to be taken out of the frame for better access Also,I did re-jet the carburetor instead of 102 I swapped it with 92 Oh Yes, and the final info: I did buy a new Stator,New Starter Engine,New Bendix,New kick-start spring , New transmission oil and intake isolator for the upgraded ...
Post a Comment
Read more

Summer project: Turbho RB-50 Retro Scooter PART#3 FINAALE

Image
Oh daym... I got way too tired of the tune up's ... I did replace the stator just this morning. Old vs New (notice that they are different) Let's not mention that the old stator's impulse 'sensor' was really worn and the poles were fouled with mud and dirt :D check it: Mehh, also the wiring was different on these two , but I did some tricks and managed to wire everything properly. In the conclusion: Yess, the old part can be thrown in the trash box with rest of the old parts AND Yes!!! The scooter performs now even much better, but I still have the 'bogging' sound present.... I took out the plug and turns out I'm running too Rich ..... What can I suggest.... Order jets for the new carb  and re-jet ? Right? That's what I thought too... :)
Post a Comment
Read more